Skip to content Skip to sidebar Skip to footer

How To Clean, Maintain, And Repair Your Garbage Disposal

How To Clean, Maintain, And Repair Your Garbage Disposal

It’s always a good idea to be prepared for serious plumbing issues. If your disposal is back in action, follow these garbage disposal do’s and don’ts to avoid issues in the future and try these tips on how to keep your drain smelling fresh no matter what food waste you send down. If our DIY plumbing tips didn’t fix your overflowing garbage disposal, then it’s time to call a professional. Before unclogging a garbage disposal, use a flashlight to look into the drain and try to find the cause of the clog. If you don’t find a clog in the trap, it may be in the part of the pipe that disappears into the wall, or even in the pipes inside the wall. If you’ve been using your garbage disposal a lot throughout the day, then the garbage disposal may have overheated and automatically turned off to prevent damage. You do not want to be cleaning a lot of this backup water yourself, so try to collect as much as you can. So, rather than waste time fixing it yourself, contact us here at United Plumbing Heating & Electric for reliable assistance!

How To Clean, Maintain, And Repair Your Garbage Disposal Try resetting your garbage disposal

If a disposal clog is the issue, there are a few ways you can go about fixing it. Let the solution soak for a few minutes before rinsing. Below are a few of them. There’s the obvious non-food stuff like bottle caps, small toys (from unknowing kids), the occasional small utensil that can find its way into the drain without your knowing, etc. But there are a handful of food-related saboteurs that may not be so obvious. The Spruce advises using a small scrub brush to remove debris that may be stuck in the trap. Lay down towels and grab a bucket to catch the water and debris that will likely come out. Disassemble the P-trap. Your garbage disposal unit will be attached to a pipe called a P- or S-trap. Hit the reset button – With any of these fixes, it’s a good idea to hit the reset button after you plug the unit back in.

How To Clean, Maintain, And Repair Your Garbage Disposal is the case

The good news is that you don’t even have to remove it to clean it. 1. To clean the splash guard, make sure your disposal is turned off at the source. Fitting down the hole doesn’t mean it made a clean getaway. Place an Allen wrench into the hole and twist until you feel the motor spin without resistance. Continue plunging until you feel that nothing else is coming up, then scoop out the material you pulled up. Once you feel you have drained the majority of the water, remove the assembly from its placement under the sink. You will need to remove the assembly by undoing the joints that are connecting it to your sink. Even if there’s no chance the unit will turn on, the blades are still sharp and could cut your fingers. Then, cut the power for the disposal with the breaker box, in case the switch is faulty. Follow the steps below if this is the case. The reset button is usually located on the bottom of the disposal but this isn’t always the case. Try resetting your garbage disposal – Most garbage disposals have a red reset button near the bottom of the unit.

How To Clean, Maintain, And Repair Your Garbage Disposal remove the assembly by

Do garbage disposals leak? A garbage disposal will only leak under two circumstances. Thanksgiving and Christmas are behind us, but another major celebratory gathering will take place this weekend. These are the miracle home systems that take on food waste like a champ. Sometimes they are mounted on the side of the disposal and if the disposal installer was paying attention they installed it so that it is easy to see and reach. Lift the plunger to see if the water drains away. Use a plunger to cover the drain. Use a flashlight to check inside and look for possible obstacles (bones, metal pieces, etc.) Pay close attention to the grind ring. Check your circuit breakers – Garbage disposals are often on their circuit in newer homes. Using a plunger is a reliable method of unclogging your Garbage Disposals. Try turning the blades manually – Garbage disposals have “breaker sockets” on the bottom that can be turned using a hex wrench.

How To Clean, Maintain, And Repair Your Garbage Disposal you plug

There are different methods you can use to unclog your Garbage Disposals before you contact a plumber. And you don’t even think about how wonderful they are until they break down and your clothes pinning your nose each time you walk by wondering, “how do I fix that smelly, malfunctioning garbage disposal? It’s best to walk on eggshells and avoid putting eggshells and coffee grounds in the disposal; however, a small amount every once in a while should be perfectly fine. Next, press the small red reset button on the bottom of the unit. Once you have confirmed the unit is off, move on to the next step. • Run water before and after you use the disposal If something has been put in the disposal that should not have been, use tongs or pliers to pull the material out. You may get a large plug of material at the end of the snake, so keep that bucket handy. Usual offenders can be large pieces of food or a foreign object (like the time I found my 4-year old’s Barbie doll head stuck in there!) If you do see something, use tongs or pliers to retrieve it. Follow the steps below to see if you can get it turning again.

How To Clean, Maintain, And Repair Your Garbage Disposal are behind us